Injection Moulding Machine for Mascara Tubes, Lip Gloss Tubes and Wands
Mascara tubes, lip gloss tubes and their wands are made on horizontal injection moulding machines, usually in multi-cavity moulds, from PP, SAN, ABS and PBT. Machine size follows the cavity count, shot weight and the mould height a long tube core needs. Core cooling and core-shift control on the deep, thin tube wall matter most.
For this set of parts, machine selection centres on repeatable shot control for the wiper and stem fits, enough opening stroke for long cores and steady mould cooling. Pratishna Engineers supplies horizontal and hybrid injection moulding machines for mascara and lip gloss components and can recommend a configuration.
Moulding Mascara and Lip Gloss Tubes?
Share the tube, wiper and wand drawings, materials and cavity plan, and Pratishna Engineers will suggest a suitable machine.
Machine Requirements for Mascara and Lip Gloss Tube Moulding
A mascara or lip gloss pack is several small mating parts, and most of the machine choice comes from the tube and the wiper fit:
- Repeatable shot and hold for the wiper interference fit
- Opening stroke and daylight for long, deep tube cores
- Core cooling and support to stop tube wall core shift
- Full venting and fine detail for moulded-bristle wands
- Drying before moulding PBT, ABS and SAN parts
- Clear SAN tubes free of flow lines and splay
Recommended Machine for Mascara Tubes and Wands
Tubes, wipers, stems and caps are small parts, so tonnage follows the cavity count and the mould height a long tube core needs. The Hybrid PH Series (120-140 T) gives electric injection for tight wiper and stem fits. The E Series (75-180 T) suits most tube and cap moulds, while the H Series (120-350 T) takes high-cavity tools with larger mould plates.
Not Sure Which Machine You Need?
Send your tube length, cavity plan and wiper design for a matched machine.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBCosmetics & Personal Care Components & Machine Guide
A guide to Cosmetics & Personal Care components, covering compacts, lipstick cases, cream jars, caps, pumps, combs, brushes and hair accessories. It explains cosmetic surface finish, thick-wall clear parts, precise mating components, and how to match each part to a suitable machine.
Download PDFPDF · 203 KB
FAQs / Buyer Questions
Questions buyers ask when they plan mascara and lip gloss tube moulding.
Which Injection Moulding Machine Is Used to Make Mascara Tubes and Wands?
A horizontal machine in the smaller tonnage bands handles these parts. Wipers and stems with tight fits often go on the Hybrid PH Series, tube and cap moulds on the E Series, and high-cavity tools on the H Series.Why Does the Wiper Decide How Much Product the Wand Picks Up?
The wiper scrapes surplus mascara or gloss off the wand as it is pulled out. Its bore against the stem is an interference fit, so a small shrinkage change alters payout. Stable hold pressure and mould temperature matter more here than extra tonnage.Can Moulded-Bristle Wands Be Made on These Machines?
Yes, when the bristles are part of the moulding. That needs a fine-detail tool with full venting so the thin bristles fill without burn marks. Twisted-wire brushes with fibre bristles are assembled on wire machines and are not injection moulded.
How Is a Clear Lip Gloss Tube Kept Free of Marks?
Clear SAN shows every flaw. Dry the resin, polish the core and cavity, and gate so that flow lines and weld lines stay off the visible wall. Moisture left in the granules shows as silver splay on the finished tube.Can Pratishna Recommend a Machine for My Mascara Tube?
Yes. Share the tube, wiper, wand and cap drawings or samples, the materials, part weights, mould sizes, cavity counts and monthly volume, and Pratishna Engineers will recommend a suitable machine.Does the Machine Suit Other Cosmetic Packaging Parts Too?
Yes. Similar machines can mould lipstick cases, caps and closures for cosmetic bottles, roll-on balls and collars, and deodorant stick containers, depending on each mould.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]