Injection Moulding Machine for Drone Frames and Components
Drone frames, arms, motor mounts, landing gear and body shells are made on horizontal injection moulding machines, typically from glass-filled or carbon-filled PA6, PA66 and PC/ABS. Machine size follows the projected area of the frame or shell and the cavity count. Gate position matters most, since weld lines at arm roots and motor-mount bosses decide crash strength.
For drone parts, machine selection centres on a wear-resistant screw and barrel for fibre-filled nylon, steady shot weight for airframe mass control and enough mould space for one-piece frames. Pratishna Engineers supplies horizontal injection moulding machines for drone components and can recommend a configuration for your part and mould.
Manufacturing Drone Frames?
Share your frame or shell drawing, material and mould details, and Pratishna Engineers will recommend a suitable injection moulding machine.
Machine Requirements for Drone Component Moulding
Drone structural parts are fibre-filled, weight-critical and have to survive a crash, so the machine must suit these points:
- Bimetallic barrel and wear-resistant screw for glass or carbon fill
- Gate position that keeps weld lines off arm roots
- Repeatable shot weight for tight airframe mass tolerance
- Drying of PA6 and PA66 before moulding
- Even cooling to limit warpage on long, thin arms
- Mould space and opening stroke for one-piece frames
Recommended Machine for Drone Components
Motor mounts, arm clamps and landing gear legs are small parts that suit the E Series (75-180 T), often in family or multi-cavity moulds. One-piece frames and body shells have larger projected areas and move up to the H Series (120-350 T) or C Series (140-320 T), with clamp and tie-bar space checked against the mould.
Not Sure Which Machine You Need?
Send your drone part drawing and fibre grade for a machine recommendation.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBDefence Sector Components & Machine Guide
A guide to Defence Sector components, covering drone frames, propellers, cowlings, gimbal housings, rugged enclosures, connector backshells and field battery housings. It explains fibre-filled engineering plastics, sealing faces, overmoulding, and how to match each part to a suitable machine.
Download PDFPDF · 207 KB
FAQs / Buyer Questions
Questions drone makers ask our engineers before choosing a machine for frames and structural parts.
Which Injection Moulding Machine Is Used to Make Drone Components?
The answer depends on part size. Mounts, clips and leg parts fit the E Series, while complete frames and larger body shells usually move to the C or H Series once mould width and projected area are known.Should Drone Frames Be Glass-Filled or Carbon-Filled Nylon?
Carbon-filled PA6 gives a stiffer, lighter frame. Glass-filled PA6 is often chosen for safety, because carbon fragments from a crash are conductive and can short the flight battery. Both grades wear the screw, so a bimetallic barrel is needed either way.Why Does Gate Position Matter on a Drone Frame?
Fibres line up with the melt flow, and where two flow fronts meet, few fibres cross the weld line. Placing the gate so weld lines fall away from arm roots and motor-mount bosses keeps those high-load areas strong.
How Is Part Weight Controlled for Airframe Parts?
Airframe mass tolerance is tight, so shot weight and holding pressure must repeat from shot to shot. Each structural part needs a weight and dimensional check, and material dried to a steady moisture level keeps the shot consistent.Can Pratishna Recommend a Machine for My Drone Component?
Yes. Share the part drawing or sample, material grade, part weight, mould dimensions, number of cavities and monthly volume, and Pratishna Engineers will recommend a suitable machine.Does the Machine Suit Other Defence Sector Parts Too?
Yes. The same class of machine can mould propeller guards, battery cowlings, rugged field enclosures and portable battery pack housings, subject to the mould and material.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]