Injection Moulding Machine for Furniture Legs, Feet and Levelling Glides
Furniture legs, feet and levelling glides are made on horizontal injection moulding machines from PP, ABS, POM or glass-filled PA6, often with a metal adjuster stud as an insert. Part size, wall section and insert loading decide machine size. Thread strength matters most, because the moulded thread carries the furniture load.
Machine selection for legs and glides weighs shot capacity for thick decorative legs against fine control for small threaded feet. Pratishna Engineers supplies horizontal injection moulding machines for furniture leg and glide moulding and can recommend a set-up around your designs.
Moulding Furniture Legs and Feet?
Tell us the leg or foot design, material, insert type and volume, and Pratishna Engineers will suggest a machine.
Machine Requirements for Furniture Leg and Glide Moulding
Legs and feet carry load in service, and decorative legs are judged on looks as well. Things to check when choosing a machine:
- Clean thread form on load-bearing adjuster feet
- Wear-resistant screw and barrel for glass-filled PA6
- Insert loading time allowed for metal adjuster studs
- Cored-out sections on thick legs to prevent sink
- Dry PA6 and POM processed without voids
- Opening stroke and mould height for long legs
Recommended Machine for Furniture Legs and Glides
Small glides and threaded feet in multi-cavity tools fit the E Series (75-180 T). Taller decorative legs with more shot weight and longer cores suit the C Series (140-320 T) or H Series (120-350 T), where opening stroke and platen size leave room for the longer mould.
Not Sure Which Machine You Need?
Share your leg or glide drawing and insert details for a recommendation.
Why Choose Pratishna Engineers?
- Application-Based Machine Selection
- In-House Engineering & Manufacturing
- Multiple Machine Series
- Production-Focused Solutions
- End-to-End Technical Support
- Industry-Specific Solutions
- Machine Lifecycle Support
Injection Moulding Machine Buyer Resources
Download practical resources to help you select, size and specify the right machine.
Horizontal Injection Moulding Machine Selection Guide
A step-by-step guide covering the key inputs needed to select the right machine: product weight, projected area, number of cavities, plastic material, required clamping force, shot / injection capacity, mould dimensions, production quantity, cycle time and automation requirement.
Download PDFPDF · 265 KB
How to Calculate Clamping Force for an Injection Moulding Machine
A clear methodology that explains how clamping force is calculated, covering projected area, injection pressure, safety factor, number of cavities and material considerations.
Download PDFPDF · 363 KBFurniture & Hardware Components & Machine Guide
A guide to Furniture & Hardware components, covering chairs, stools, tables, drawers, storage, hinges, drawer channels, knobs, castors and fittings. It explains large-part moulding, mould height, POM and nylon hardware, and how to match each part to a suitable machine.
Download PDFPDF · 203 KB
FAQs / Buyer Questions
Points furniture makers raise when planning leg and glide production.
Which Injection Moulding Machine Is Used to Make Furniture Legs and Glides?
Glides and levelling feet usually run on E Series machines in multi-cavity tools. Longer or heavier decorative legs move to the C or H Series, chosen by shot weight, mould height and opening stroke.Why Use POM or Glass-filled Nylon Instead of PP for Levelling Feet?
PP creeps under constant load, so a threaded foot in PP can sink or strip over time. POM and glass-filled PA6 hold the thread form under the weight of the furniture. PP still suits light glides and leg caps.How Is Sink Avoided on Thick Plastic Legs?
Thick sections shrink unevenly and leave sink marks on the visible face. Coring out the leg to a more even wall, with ribs for stiffness, and enough holding pressure near the gate keep the surface flat.
Should the Adjuster Stud Be Moulded In or Pressed In?
Moulding the stud in gives a stronger joint but adds insert loading to every cycle. Pressing the stud in after moulding keeps the cycle shorter. The choice depends on the load rating and volume.Can Pratishna Recommend a Machine for My Furniture Leg or Glide?
Yes. Share the leg or foot drawing, material, part weight, insert details, cavities, mould size and monthly quantity, and Pratishna Engineers will recommend a machine.Does the Machine Suit Other Furniture Parts Too?
Yes. Caster wheels, trolley wheels, pipe end caps and furniture knobs are among the related parts these series can mould, depending on the mould.
Technical Disclaimer
Disclaimer: The information provided in this webpage is for general informational and educational purposes only. It is based on technical references and industry information available at the time of preparation and may be subject to change. It does not constitute engineering, technical, commercial or professional advice, nor does it constitute a quotation, specification, warranty or contractual commitment by Pratishna Engineers.
Actual injection moulding machine and process requirements vary according to the component design, material, mould, production volume, machine configuration and operating conditions. The information, examples, calculations and recommendations provided should be independently evaluated and verified for the specific application before making any equipment, process or production decision. Information obtained from third-party sources remains subject to the accuracy and limitations of those sources.
Limitation of Liability: Pratishna Engineers makes no representation or warranty, express or implied, regarding the completeness, accuracy or suitability of the information for any particular application. To the extent permitted by applicable law, Pratishna Engineers shall not be liable for any loss, damage, cost or consequence arising from reliance on or use of the information contained in this webpage. Final machine selection, configuration and application suitability should be confirmed with Pratishna Engineers based on complete and accurate project requirements.
Talk to Our Engineers
Planning a New Injection Moulding Project?
Share your component, material, mould and production target. Our engineering team will help you identify the right machine configuration.
- Machine Sales
- +91 99690 38542
- Service Support
- +91 97689 28259
- Sales Email
- [email protected]